Product Description

The Club Smoke System is a unique two-head smoke package with a "ground-based" fluid supply specifically designed for club installations. This special smoke delivery system blends into any club d?cor with the compact smoke heads continually delivering a high volume of dense white smoke.

The split system allows the two smoke heads to be installed in inaccessible areas such as in high trussing, club ceilings or under floors, while the fluid supply (10 liter) and pump system (wall mounted Service Module) is installed in a more convenient location such as the DJ booth or storage cupboard. No more high-wire fluid refills! The Club Smoke System is also DMX compatible (on service module).

The systems reliability is enhanced by the inclusion of the Electronic Low Fluid Cut Off System and overheat protection. Other great features include a multifunctional, auto timer remote featuring 8X mode and smoke output level control. High output is guaranteed thanks to the trusted design of Jem?s 1000W vaporizing system fitted to both smoke heads. Furthermore a sturdy "U" bracket allows the head to be mounted at any angle.

Heater size

1000w

Total power consumption

4.8A @ 220-240v

9.5A@ 110v Fuse rating

10A @ 220-240v

20A @ 110v

Heat up time

7 mins Operation time

Continuous

Over-heat protection

Direct Thermal Protection Device Controller supplied

Jem Multifunctional remote control

Control Options

0-10v input DMX input

On-board 1 channel required for variable output

0-10v input

Use remote XLR socket Pin 1 GND and Pin 3, 0-10v input. This pin needs 1.5v to heat the machine and 2-10v to run the pump when up to working temperature. Analog link

Standard via 3 pin XLR socket

Fluid capacity

9.5 litre Recommended fluid

Pro Smoke Studio (DX Mix)

Pro Smoke Super (ZR Mix)

Pro Smoke Super (Fragranced)

Pro Smoke High Density (SP Mix)

Fluid consumption (max.)

75ml/min

0.018 Imp. gallon/min Fluid level sensing

Standard

Input fluid pipe diameter

2x O/D 6mm Smoke Output (approx. each head)

500 cubic metres/min

17657 cubic feet/min

Dimensions of Smoke Head

330mm x 310mm x 165mm Dimensions of Service Module

410mm x 480mm x 290mm

Dimensions of 2 Smoke Heads When Boxed

810mm x 380mm x 390mm Dimensions of Service Module Boxed

580mm x 520mm x 440mm

Weight of Each Smoke Head

10kg Weight of Service Module With Fluid

12kg without fluid

22kg with fluid

Flying kit

Standard Drip tray

Standard Installation

The machine should be located in a well-ventilated area with a minimum of 200mm air space around the sides and top of the machine. The machine should only be used on level surfaces. The initial smoke output of the machine is hot, so the front of the machine should at least 1 metre from surfaces or people. Never leave the machine running unattended. Do not install above people?s heads. Ducting kit

Optional 4 " flexible inc. adapter

Output nozzle size

40mm dia Max length of remote cable

50 metres (10 metres supplied)

Accessories

4 " Flexible Ducting System inc. Adapter

Flying kit inc. drip tray

Drip tray Sample project specification

Description
The Club Smoke System is a two head smoke package with "ground based" fluid supply specifically designed for club installations.

Soft Start Electronics
The "crack" created during the initial burst of smoke is caused by the pump pressure overcoming the incredible back pressure of the heat exchanger. Jem?s unique Soft Start Electronics gradually powers the pump, eliminating this crack and ensuring a quieter and smoother operational level following initial start up.

Electronic Low Fluid Cut-off System
This technology is fitted to all machines designed for continuous operation. To eliminate the risk of running dry and burning out the pump, this unique electronic sensing system will automatically shut-off the machine, protecting all major components.

Heat exchanger
All Jem heat exchangers are designed for high efficiency performance. Only the purest grade LM24 aluminum is used in the production process which eliminates the risk of porosity (pockets of gas within the casting which can cause heater failure). All heat exchangers contain cuprous helicoils of at least 2.8 meters in length, ensuring a continuous flow of pure, dry, white smoke.

Electronic Pump Ramping
Jem was the original pioneer of EPR, an intelligent means of warning of a drop in temperature which could result in ?wet smoke? (residue). The pumps respond to this signal by running slower and pumping less fluid, thus allowing the heaters to restore optimum operational temperature. This guarantees a continuous flow of smoke using highly efficient, lower wattage heaters.

Jem Multifunctional Remote
This reliable remote offers more than the usual auto timer and smoke level output controls. Easily engaged, the timer gives complete adjustment for both ?Fog On? and ?Fog Delay? modes. These timer functions can be expanded even further by engaging Jem?s unique ?8X Mode? which multiplies the selected timer setting by eight.

DMX Control
This uses a single channel of DMX 512 giving a full variable output from the machine. This important feature means that atmospheric effects can now become choreographed into the Light show or stage performance via the lighting console.

Analogue Link
Whether you?ve run out of DMX channels or simply want to link two smoke machines together and operate them from a single remote, Jem?s analogue link facility is the solution. This feature even allows multi-machine connection, making operation a simple one-finger action.

Direct Thermal Protection Device
This small yet crucial component is the last line of defense against catastrophic failure. Other manufacturers still depend on cheap plastic whereas Jem?s DTPD is made from a solid ceramic composite. This guarantees extremely precise overheat monitoring and is unaffected by ambient temperature changes.

Max Power Consumption
4.8A @ 220v
9.5A @ 110v

Maximum Smoke Output
500 cubic metres/min
17,657 cubic feet/min

Fluid container
All Jem smoke, haze and heavy fog machines are designed to carry removable fluid containers of varying sizes depending on the models application. The removable container makes for quicker refills and protects the machine from damage through spillage in transit.

Maximum Fluid Consumption
75ml/min
0.018 Imp. gallon/min

Accessories
Ducting system
Extra lengths of 6mm fluid line
Extra lengths of data cable

Included items
2x Smoke heads
1x Service module
Jem Multifunctional remote control
9.5 litre fluid container (empty)
2x 10metres of 6mm fluid line
2x 10 metre data cables
2x Drip trays
DMX control
Instructions for use manual

Recommended fluids
Pro Smoke Studio (DX Mix)
Pro Smoke Super (ZR Mix)
Pro Smoke Super (Fragranced)
Pro Smoke High Density (SP Mix)